Temp, Inc. Instrumentation Specialists
Your Place for Standard or Custom SCR Power Controllers, Temperature Controllers, Digital Panel Meters, Monitors and Motor Controls, Transducers,  Solid State Relays
for
Industrial Electric Heating Applications
 

Home
Company Information
SCR Power Controllers
Temperature Controllers
Digital Panel Meters
Solid State Relays
Three Phase Voltage Monitors
Transducers
Temperature Monitors and Motor Controls
Distributors
Catalog Sales
AC Current Transducers

Features

 
Dcp_0010.jpg (9217 bytes)

Models:

S3-AD-1 -   Single Phase input (AVG)

S3-AD-3 -   Three Phase input (AVG)


S3-AD-1T - Single Phase input (TRMS)

 

 

 

bullet Accuracy (+ or - 0.2% RO)
bullet Excellent long term stability (4-20ma, 500 ohm)
bullet Precision measurement even for distorted wave (S3-AD-1T)
bullet High Impulse & surge protection (5KV)
bullet The case can be mounted on a 35mm rail which complies with DIN 46277

 

Sinusoidal Waveforms -  AVG

S3-AD Series Transducer converting a sinusoidal alternating voltage into a dc output,
proportional to the RMS value of input.  These units are average sensing, but RMS
calibrated for a sine wave with less than 1% distortion.  The input signal is converted
 to a dc voltage which then feeds to a single amplifier and a dc output produced.
 

waveform1.JPG (8598 bytes)

 

 

Non-Sinusoidal Waveforms - TRMS

S3-AD-1T Transducer are designed for use on waveforms with up to 30% of
3rd harmonic content.  The input signal is fed to an RMS detection circuit
and the resultant dc volts produced are a linear function of the RMS value
of input waveform.  This dc voltage is converted to a milliamp output via an
output amplification circuit.

 waveform2.jpg (8303 bytes)

 

Input-Output Curve

waveform3.jpg (7787 bytes)

 

SPECIFICATIONS

 

Input

Input
Range

Input Burden

Input Frequency

Max. Input
Over Capability

0-5A

< 0.2VA

 

50Hz (+ or -) 3Hz
or
60Hz (+ or -) 3Hz

 

3 x rated continuous
10 x rated 10 sec.
50 x rated 1 sec.

0-10A

 

Output

 
DC Output Range Load
Resistance		 Output
Resistance		 Output
Ripple		 Response
Time
0-1V > 1K Ohm < 0.05 Ohm < 0.5% RO
(Peak)		 < 400mS
0-99%
0-5V
1-5V
0-10V
0-1mA 0-10K Ohm > 20M Ohm
0-10mA 0-1K Ohm  
0-20mA 0-500 Ohm 0-500 Ohm
4-20mA

 

Accuracy + or - 0.2% rated of Output
Aux. power supply AC 110V (+ or -) 15%, 50/60 Hz
AC 220V (+ or -) 15%, 50/60 Hz
DC 24V, 48V, 110V, (+ or -) 15%
 
Power consumption (<) 2.5VA, (+ or -) DC 3W
Power effect (<) 0.% RO
Waveform effect (<) 0.2% RO at distortion factor 30%
(S3-AD-1T)
Output load effect (<) 0.05% RO
Magnetic field strength (<) 0.2% RO, 400 A/M
Span adjustment (>) 5% RO
Zero adjustment (>) 1% RO
Operating temperature range 0-60 degrees C
Storage temperature range (-) 10-70 degrees C
Temperature coefficient (<) 100PPM from 0-60 deg. C
(<) 60 PPM, 25 deg. C (+ or -) 10 deg. C
Max. relative humidity 95%
Isolation Input/Output/Power/Case
Insulation resistance (>) 100M ohm, DC 500V
Dielectric withstand voltage
(IEC 414, 688, ANSI, C37)		 Between input/output/power/case
ac 2.5kv, 60Hz, 1 min
Impulse withstand test
(IEC 255-4, ANSI, C37 90)		 5 kv, 1.2 x 50 nS
common mode & differential mode
Performance Designed to comply with IEC688
Safety requirements IEC 414, BS5458

Back to Transducers